HILTI Main Menu Table of Contents Selection Guide Firestop Program HAP Program Decking Program HILTI Web Site Search Submittal Package
Product Description Product Approvals Material Specifications Installation Ordering MSDS

HILTI LOGO COLOR
MSDS No:230
Revision No:002
Date:05/12/97

MATERIAL SAFETY DATA SHEET

HILTI, INC.:
P.O. Box 21148
Tulsa, OK 74121
Ph: 1 800 879 6000
Emergency No.: 1 800 879 4444

PRODUCT NAME: CI 060 EP Epoxy Injection Resin (Parts A and B)

DESCRIPTION: Epoxy Injection Resin with Amine Hardener

INGREDIENTS AND EXPOSURE LIMITS

INGREDIENTS:CAS NUMBER:PEL:TLV: STEL:
Part A: Epoxy resin25068-38-6NENENE
o-Cresyl glycidyl ether02210-79-9NENENE
Part B: Pentaethylenehexamine04067-16-7NENENE
Benzyl alcohol00100-51-6NENENE

PEL = OSHA permissible exposure limit (as revised 01/19/89). TLV = ACGIH threshold limit value. These are 8 hour time-weighted averages unless otherwise indicated by "C" (Ceiling) or "STEL" (Short Term Exposure Limit). NE = None Established.

PHYSICAL DATA

APPEARANCE AND ODOR: Part A: Clear liquid. Slight odor. Part B: Amber liquid. Amine odor.
SPECIFIC GRAVITY: 1.0 - 1.2pH: 11 (Part B)
BOILING POINT: >200°CVOC CONTENT: Not Determined
VAPOR PRESSURE: 0.01 mbarVAPOR DENSITY: Not Determined
EVAPORATION RATE: Not DeterminedSOLUBILITY IN WATER: Miscible

FIRE AND EXPLOSION HAZARD DATA

FLASH POINT: 280°F (138°C) FLAMMABLE LIMITS: Not Applicable

EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water

SPECIAL FIRE FIGHTING PROCEDURES: A self-contained breathing apparatus should be used when fighting fires involving chemicals.

UNUSUAL FIRE AND EXPLOSION HAZARDS: None known. Thermal decomposition products can be formed.

REACTIVITY DATA

STABILITY: Stable.

INCOMPATIBILITY: Strong acids, peroxides, and other oxidizing agents.

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition can yield carbon dioxide and carbon monoxide.

HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Exposure to excessive heat or storage above 100°F will shorten the shelf life of this product.

HEALTH HAZARD DATA

KNOWN HAZARDS: Irritation. Sensitization.

CARCINOGENICITY: No ingredients are classified by IARC, NTP, or OSHA as known or potential carcinogens.

PRIMARY ROUTES OF EXPOSURE: Dermal. Inhalation.

SIGNS AND SYMPTOMS OF EXPOSURE: Irritates the eyes and skin. Prolonged contact with the skin can cause burns. Epoxy resins can cause an allergic reaction (rash, redness, itching, swelling) in some (susceptible) individuals.

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Eye, skin, and respiratory conditions.

EMERGENCY AND FIRST AID PROCEDURES

EYES: Immediately flush with plenty of water. Call a physician.

SKIN: Wash with soap and water. Launder contaminated clothing before reuse.

INHALATION: Move victim to fresh air. Give oxygen and/or artificial respiration if needed. Call a physician.

INGESTION: Give plenty of water to drink. Never give anything by mouth to an unconscious person. Do not induce vomiting unless directed to by a physician. Call a physician immediately.

OTHER: Referral to a physician is recommended if there is any question about the seriousness of the injury/ exposure.

CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT

VENTILATION: General (natural or mechanically induced fresh air movements that maintain vapor concentrations below recommended exposure limits).

EYE PROTECTION: Chemical goggles.

SKIN PROTECTION: Impermeable (neoprene or rubber) gloves recommended.

RESPIRATORY PROTECTION: None normally required. Use a NIOSH-approved organic vapor respirator when air movement is not adequate to control vapor concentrations. Never enter a confined space without an appropriate air-supplied respirator (e.g., SCBA or airline with escape pack).

PRECAUTIONS FOR SAFE HANDLING AND USE

HANDLING AND STORING PRECAUTIONS: Practice good hygiene; i.e., wash hands after using and before eating or smoking. Keep in a cool dry place out of direct rays of the sun. Store below 100°F. Keep from freezing. Wear appropriate personal protective equipment. Avoid contact with eyes, skin and clothing. Avoid breathing vapors. Use with adequate ventilation.

SPILL PROCEDURES: Cover with absorbent material and place in a salvage container for proper disposal. Keep away from sanitary sewers and other waterways.

REGULATORY INFORMATION

HAZARD COMMUNICATION: This Material Safety Data Sheet has been prepared in accordance with the federal OSHA Hazard Communication Standard.

HMIS CODES: Health 2, Flammability 1, Reactivity 0, PPE B, Goggles

DOT SHIPPING INFO: Non-regulated.

TSCA INVENTORY STATUS: Chemical components listed on TSCA inventory.

SARA TITLE III, SECTION 313: This product does not contain any toxic chemicals which are subject to reporting under Section 313 of SARA Title III (40 CFR Part 372).

WASTE DISPOSAL METHODS: Consult with regulatory agencies or corporate personnel for disposal methods that comply with local, state, and federal health and environmental regulations.

HEALTH / SAFETY CONTACTS:
Steve Gerrard (x6309)
Jerry Metcalf (x6704)

The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or warranty of any kind expressed or implied is made with respect to the information provided.


[MAIN MENU] [TABLE OF CONTENTS] [SELECTOR GUIDE]
[FIRESTOP PROGRAM] [HAP PROGRAM] [DECKING PROGRAM]
[HILTI WEB SITE] [SEARCH] [SUBMITTAL PACKAGE]

[Product Description] [Product Approvals] [Guide Specifications] [Material Specifications] [Technical Data]
[Installation] [Ordering] [MSDS] [Video] [Product Data]